Logotipo Texsa, S.A.

MORTERPLAS SBS FP 4 KG

MORTERPLAS SBS FP 4 KG is a waterproofing membrane that is not self-protected, made of SBS elastomeric bitumen, reinforced with high density polyester felt (FP), and finished with a thermally bonded film on both the upper and lower side.

Technical documentation

  • Logo Facebook
  • Logo Twitter
  • Logo Linkedin
  • Advantages
  • Application
  • Installation
  • Storage
  • Regulations
• Confers excellent mechanical properties to the membrane:
• Maximum puncturing resistance (static and dynamic)
• High tear resistance
• Good dimensional stability.
· It is especially recommended in applications where maximum puncturing resistance is needed.
· MORTERPLAS SBS FP can be applied in a double-layer system on non-trafficable and trafficable roofs for pedestrians and vehicles, with heavy protection.
· For single-layer systems, a membrane with a mass ≥ 4 kg will be used in systems in accordance with the DITs and local construction regulations.
· MORTERPLAS FP 4 kg can be applied as a membrane to ensure the watertightness of underground structures

Single and multi-layer flat roofs Walls.
· SUPPORT: The surface must be dry, firm, even, clean and free of loose materials.
· It can be applied completely adhered, partially adhered or floating. · To adhere the membrane to the support, the support is primed with EMUFAL I. Once dry, use flame to adhere the membrane.
· The flame is applied as uniformly as possible (the greater the heat, the greater the retraction) along the width of the membrane without reaching the overlap, which will be done later, since it is important that the temperature be the same in every area. The flame should be applied until the anti-adherent film pore opens.
· The membranes are installed in such a way that no more than three membranes overlap at the same point.
· Overlaps are flame-bonded, with a minimum overlap of 8 cm.
· In the two-layer solution, the top membrane must be completely adhered to the bottom membrane, and it must be placed in the same direction so that the overlap lays approximately in the middle of the bottom membrane.
· Installation and measurements will be conducted in accordance with regulations of the UNE 104401 standard.
Roll: 1 m x 10 m
Pallet: 270 m²
· In accordance with the EN 13707, EN 14695 and EN 13969-T standards. Certified with CE marking No. 0099/CPD/A85/0087
· Voluntary certification of the product with AENOR seal according to the same European standard.
· With DIT No. 516 Inverted roof systems “TEXLOSA® ROOFING SYSTEMS.”
· With DIT No. 562/10 MORTERPLAS/MOPLAS ZERO slope
· With DIT No. 579/11 MORTERPLAS VEHICULAR TRAFFIC
· With DIT No. 580/11 UNDERGROUND STRUCTURES MORTERPLAS
· Quality System in accordance with ISO:9001

Related Systems

1234567

Related Products

 

DATA PROTECTION

 

In cases where the user must provide data of a personal nature to TEXSA SYSTEMS SLU to use any of the Web services, the former will be expressly informed each time of the existence of an automated data base, the aim of same, those receiving the information and identity and address of the person responsible for data treatment, all with the aim of complying with that stipulated in Organic Law 15/1999 of 13th December, for the Protection of Data of a Personal Nature. To this effect, TEXSA SYSTEMS SLU shall reserve confidentiality of the data obtained and the users can exercise all rights to access, amendment, cancellation and any others referred to in aforementioned Organic Law 15/1999.

TEXSA SYSTEMS SLU has adopted all the necessary measures of a technical and organisational nature, to guarantee the security of the data of a personal nature, with the aim of preventing their alteration, loss, treatment or unauthorised access, in accordance with the requirements and conditions called for by Royal Decree 994/1999 of 11th June, in which the Regulation of safety measures of automated files containing data of a personal nature, is passed, notwithstanding the user's acceptance and knowledge that to date totally impregnable safety measures do not exist.

In case of doubt or the need to extend the information covering any of the above items, please do not hesitate to contact TEXSA SYSTEMS SLU.

 

TEXSA SYSTEMS SLU.
C/Ferro Nº7,
Polígono Industrial Can Pelegrí,
Castellbisbal
08755, Barcelona - Spain
NIF B66067687

Tel. (+34) 93 635 14 00
Fax (+34) 93 635 14 80

Email:  lopd@texsa.com